Quarrying

High technological competence. Cargo handling specialist, for energy and civil engineering applications.

FERRI takes our vocation for service to industry beyond the bounds of the maritime sector.  We are used to working with the minimum opportunities for service and maintenance and extreme working conditions. Through our technical team, we transfer our experience acquired in the development of maritime equipment to a series of different areas in which the key factors are extreme working conditions, in hostile environments.

Since 1984 we have been developing drilling machinery for ornamental quarrying and has offered an extensive range of high-performance drilling. Meeting the needs of the construction sector, we have developed a range of high-performance multifunction robots. Units able to operate in explosive or radioactive difficult access.

SPECIAL DRILLING RIG

FERRI Roll-over

Due to its engineering interests and needs identified in the market, Ferri has designed and developed special machinery among which are worth noting the following equipment. Drill pipe with the option to develop uprising processes. It has been developed in conjunction with Atlas Copco adapting drilling columns existing on the market for specific uses.

Roll-Over system is designed to perform the following movements when the drill is in uprising position:
– Horizontal turn of 220°.
– Column support with three support legs driven by hydraulic cylinders which allow the soil to 250mm shoemakers.

PNEUMATIC POWERED DRILLING RIG

FERRI N-series

Pneumatic powered drilling rigs for Stone drilling and Stone dimensioning Works. It can be attached to any back-hoe. Standard configuration: From F1N (one hammer) to F5N (five hammers). Air or water flushing. Drilling speed 1 m/min (depending on stone hardness).

DRILLING RIG WITH 1 PNEUMATIC ROCK DRILL

– Drills a bore hole up to 2.20 m in depth, end-of-travel regulated, perfectly aligned along length of 3,3 m between bore hole ends, up to 9 m in depth with drill steel change.
– Drilling speed of 0.5 in granite, 1 m/min in marble. Average drilling rate of 250 m/day in granite.
– Drilling speed of 0.5 in granite, 1 m/min in marble. Average drilling rate of 250 m/day in granite.
– A 24 kg pneumatic rock drill for integral 7/8″ drill steels, 32 mm diam.
– Fixed manual controls. Optional remote control.
– Pressurized water flushing of bore holes, with a consumption of 7 l/min. 2.000-litre tank and pump are coupled to the vehicle.
– Optional air flushing with dust retainer.
– The compressed air for the operation of the machine (3,5 m³ at 6 bar), will be provided by external compressor.
– They can be installed on excavators with a minimum weight of 10 tons.

DRILLING RIG WITH TWO PNEUMATIC ROCK DRILLS

– Drills two bore holes at the same time of up to 2.20 m in depth, end-of-travel regulated, perfectly aligners aling a length of 3.6 m between bore hole ends, up to 9 m in depth with drill steel change.
– Drilling speed of 0.5 m/min in granite, 1m/min in marble.
– Average drilling rate of 250 m/day in granite.
– Two 24 kg pneumatic rock drills for integral 7/8 drill steels, 32 mm diam.
– Fixed manual controls. Optional remote control.
– Pressurized water flushing of bore holes, with a consumption of 7 l/min.
– 2,000-litre tank and pump are couples to the vehicle.
– Optional air flushing with dust retainer.
– The compressed air for the operation of the machine (7 m³ at 6 bar), will be provided by external compressor.
– They can be installed on excavators with a minimum weight of 10 tons.

DRILLING RIG WITH THREE PNEUMATIC ROCK DRILLS

– Drills three bore holes at the same time of up to 2,20 m in depth, end-of-travel regulated, perfectly aligned along length of 3,62 m between bore hole ends, up to 9 m in depth with drill steel change.
– Drilling speed of 0,5 in granite, 1 m/min in marble. Average drilling rate of 450 m/day in granite.
– Three 24 kg pneumatic rock drills for integral 7/8″ drill steels, 32 mm diam.
– Fixed manual controls. Remote control is also available.
– Pressurized water flushing of bore holes, with a consumption of 12 l/min. 3.000-llitre tank and pump are coupled to the vehicle.
– Optional air flushing with dust retainer.
– The compressed air for the operation of the machine (15 m³ at 6 bar), will be provided by external compressor.
– They can be installed on excavators with a minimum weight of 16 tons.

SEMI-AUTOMATIC DRILLING RIG WITH FOUR PNEUMATIC ROCK DRILLS.

– Drills four bore holes at the same time of up to 2,20m un depth, automatically regulated, perfectly aligned along a length of 4.14 m between bore hole ends, up to 9m in depth with drill steel change.
– Four 29-kilo pneumatic rock drills for integral 7/8 drill steels, 32 mm Diam.
– Drilling speed of 0.75 m/min. In granite, 1,5 m/min in marble.
– Average drilling rate of 600 m/day in granite.
– Controlled either from the machine’s cabin or portable push-button control.
– Optional radio control of the rig and the excavator.
– Pressurized water flushing of bore holes, with a consumption of 16 l/min.
– 4,000-litre tank and pump are coupled to the vehicle.
– Optional air flushing with dust retainer.
– The compressed air for the operation of the drilling rig (20 m³ at 6 bar), will be provided by external compressor.
– Can be installed on excavators with a minimum weight of 17 tons.

SEMI-AUTOMATIC DRILLING RIG WITH FIVE PNEUMATIC ROCK DRILLS

– Drills five bore holes at the same time of up to 2.20 m in depth, automatically regulated, perfectly aligned along a length of 4.4 m between bore hole ends, up to 9 m in depth with drill steel change.
– Five 29-kilo pneumatic rock drill for integral 7/8 drill steels, 32 mm Diam.
– Drilling speed of 0.75 m/min. In granite, 1.5 m/min in marble.
– Average drilling rate of 750 m/day in granite.
– Controlled either from the machine’s cabin or portable push-button control.
– Optional radio control of the quarrying machine and the excavator.
– Pressurized water flushing of bore holes, with a consumption of 20 liters/minute.
– 4,000-litre tank and pump are coupled to the vehicle.
– Optional air flushing with dust retainer.
– The compressed air for the operation of the drilling rig (25 m3 at 6 bar), will be provided by external compressor.
– Can be installed on excavators with a minimum weight of 18 tons.

HYDRAULIC POWERED DRILLING RIG

FERRI H-series

Hydraulic powered drilling rigs for Stone drilling and Stone dimensioning Works. It can be attached to any back-hoe. Standard configuration: F2H (two drifters), F3H (three drifters). Air or water flushing. Drilling speed 1 m/min (it depends on stone hardness).

SELF CONTAINED DRILLING RIG WITH ONE HYDRAULIC ROCK DRILL

– Drills one bore hole of up to 2.20 m in depth, end-of-travel regulated, and can produce a perfectly aligned line of bore holes with a length of 3.35 m between bore hole ends.
– One hydraulic rock drill for integral 7/8 drill steels, 32mm Diam.
– Drilling speed of 1 m/min in granite, 2 m/min in marble.
– Average drilling rate of 250 m/day in granite.
– Fixed manual controls. Optional portable control.
– Pressurized  water  flushing of bore holes, with a consumption of 5 l/min.
– 2000-litre tank and pump are coupled to the vehicle.
– Optional air flushing with dust retainer.
– Can be installed  on excavators with a minimum weight of 10 tons and 80 hp.
– The compressed air for the operation of the machine (3,5 m³ at 6 bar), will be provided by external compressor.
– They can be installed on excavators with a minimum weight of 10 tons.

SEMI-AUTOMATIC SELF-CONTAINED DRILLING RIG WITH TWO HYDRAULIC ROCK DRILLS

– Drills two bore holes at the same time of up to 2.20 m in depth, automatically regulated, perfectly aligned along a length of 3.6 m between bore hole ends, up to 9 m in depth with drill steel change.
– Two Hydraulic rock drills for integral 7/8 drill steels, 32 mm Diam.
– Drilling speed of 1 m/min in granite, 2 m/min in marble.
– Average drilling rate of 550 m/day in granite.
– Controlled either from the machine’s cabin or remote radio control.
– Fully automatic anti-jamming function and automatic reset. Control and recording of daily production and accumulated totals.
– Pressurized water flushing of bore holes, with a consumption of 10 l/minute.
– 4000-litre tank and pump are coupled to the vehicle.
– Optional air flushing with dust retainer.
– Can be installed on excavators with a minimum weight of 19 tons.

SEMI-AUTOMATIC SELF-CONTAINED DRILLING RIG WITH THREE HYDRAULIC ROCK DRILLS

– Drills three bore holes at the same time of up to 2.20 m in depth, automatically regulated, perfectly aligned along a length of 4.14 m between bore hole ends. Up to 9 m in depth with drill steel change.
– Three hydraulic rock drills for integral 7/8 drill steels,32 mm Diam.
– Drilling speed of 1 m/min in granite, 2 m/min in marble.
– Average drilling rate of 800 m/day in granite. – Controlled either  from the machine’s cabin or remote radio control.
– Fully automatic anti-jamming function and automatic reset. Control and recording of daily production and accumulated totals.
– Pressurized water flushing of bore holes, with a consumption of 15 l/minute. – 4.000-litre water tank and pump are coupled to the vehicle.
– Optional air flushing with dust retainer.
– Can be installed on excavators with a minimum weight of 21 tons.

NOS VEMOS EN:

MEET US AT THE EXHIBITION:

RENCONTREZ-NOUS À L’EXPOSITION:

ONTMOET ONS OP DE TENTOONSTELLING:

TREFFEN SIE UNS AUF DER MESSE:

STAND F67